Call us for free now: 07 3219 6711 service@sa-led.com
SKU: SA 1645G Categories: , , ,

SA N2-4 LED Neon Flex 24V Orange (9.6W/M)


Variation NAME PRICE Stock
[ SA1645G-5 ] 5M ($41.01/M) $205.05 4
[ SA1645G-10 ] 10M ($38.83/M) $388.31 5
[ SA1645G-20 ] 20M ($36.23/M) $724.51 3

Key Features & Benefits:

Item Code : SA 1645G
Fabricated with Eco-friendly
UV-resistant silicone material
IP67 rate
Flexible PCB with SMD LED technology
24V DC low voltage, safe and reliable
Cutting mark by every 50mm

We strongly recommend both end power input at all length

5years Warranty


ALTERNATIVE PRODUCT

    SA N2-4 LED Neon Flex 9.12W 12V Orange (5 Metre / Unit)

    $407.13 $205.05 excl. g.s.t

    Key Features & Benefits:

    Item Code : SA 6649G
    Fabricated with Eco-friendly
    UV-resistant silicone material
    Flexible PCB with SMD LED technology
    12V DC low voltage, safe and reliable
    IP67 rate
    Cutting mark by every 26.32mm

    We strongly recommend both end power input at all length

    5years Warranty

    Availability: 4 in stock

Clear selection

Share it:
Power Calculator

METRE Indoor Outdoor

 

 

Special Note

ROLL LENGTHS_Any claim for short supply will only be considered while
the NEON FLEX is in one length, to prove any manufacturing discrepancy.

*Note that once you cut the roll it will void any claim for short supply of the product.

Troubleshooting Common Faults

Problems Reasons Solutions
No illumination No electricity supply Ensure LED driver is working
Automatic power protection from the open or short circuit in output of the power supply Fix the short circuit problem
Wrong connection of power supply
Partial illumination Using a switching mode power supply Make it as follows: Don’t use switching mode power supplies
Wire connection mistake Check connections
Brightness of LED is inconsistent for inconsistent Power overloaded Replace with a power supply that delivers 125% of current required to power the product
Voltage drop due to exceeding max-in-series limit Adhere to the max-in-series limit specified on the product page
LED Flickering Connection point fault Fix bad connection point
Use a proper LED driver Replace a new power supply

*Note that should be cut and reconnected with end connectors for installation to avoid defects due to moisture penetration. The steps below indicate are possible way of sealing the end :

Installation steps

Cut the neon flex First put silicone glue inside
of the plug, and quick connector
then push into the neon flex
Wipe off the excess glue and
wait for the glue to solidify.

[ Important Notice ] LED NEON FLEX_GUIDE

SA LED NEON FLEX 24V YELLOW (9.6W/M)

Products Features

How to install LED NEON FLEX

Important Note

Installation Precautions

1. All installation and connection must be conducted by qualified electrician.

2. A 24V DC class 2 power supply unit must be used with this LED NEON FLEX.

3. Disconnect the mains power before installing or servicing to avoid electrocution.

4. For a wet location installation you must seal all possible water entry points including covers with clear silicone.

Dimensions(mm)

LED CASES

Dimensions 8 × 1300 × 12 mm
MODEL

SA UNIVERSAIL NEON FLES 24V ORANGE

POWER

9.6W/M

CURRENT(A)

0.4A

VOLTAGE

DC 24V

LENGTH

[ SA1645G-5 ] 5M ($41.01/M), [ SA1645G-10 ] 10M ($38.83/M), [ SA1645G-20 ] 20M ($36.23/M)

LUMINOUS FLUX

140lm

EFFICIENCY

14lm/W

COLOUR

ORANGE

CRI

80

VIEWING ANGLE

180°

IP RATING

IP67

DIMMABLE

DIMMABLE

CUTTABLE

50mm

AVAILABLE LENGTH

10M, 20M, 5M

LED Qty/m

120

WARRANTY

5 YEARS

Reviews


Be the first to review “SA N2-4 LED Neon Flex 24V Orange (9.6W/M)”

*

Navigation

MY CART

Close

No products in the cart.

No products in the cart.

WISHLIST

Close

No products were added to the wishlist