Sale
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![SA LED SLIM NEON FLEX PURE WHITE 12V 11.52W/M](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
![](https://sa-led.com/wp-content/themes/woodmart/images/lazy.png)
For expert tips and tutorials to take your lighting projects to the next level.
Innovating with Sustainable Aluminium Extrusions
Item Code | Price | Stock |
SA 10C-15M | $ 465.05 | 4 |
SA 10C-30M | $ 929.66 | 3 |
$465.05 – $929.66 Excl. GST
DOWNLOADS
Check out the latest product specifications and guides.
Product Specification
Installation Guide
IES File
Power Calculator
Easy to estimate your power supply needs.
Our power calculator helps you determine the power supply needed for your LED light projects.
*Simply answer the questions below, and you'll receive a quick recommendation.
Use one power supplier per single piece of neon flex over 20M.
Enter the required number of the LEDs or Metre
METREWhere will the power supplies be installed?
e.g) Strip or Neon Flex : 8 Metres
60 in stock
Range | Price |
---|---|
Box -100 Connectors | $19.73 $0.32 / each |
Dimension
Weight | 900 g |
---|---|
Dimensions | 5000 × 11 × 12 mm |
POWER |
15.36W |
VOLTAGE |
DC 24V |
CURRENT(A) |
0.625A |
LUMINOUS FLUX |
332lm |
EFFICIENCY |
22lm/W |
COLOUR |
YELLOW |
CRI |
80 |
IP RATING |
IP 68 |
DIMMABLE |
DIMMABLE, Dimmable with HLG Power Only |
CUTTABLE |
62.5mm |
LENGTH |
15M, 30M |
WARRANTY |
5 YEAR |
SA 10C NDR2018-VERTICAL-LED-NEONFLEX 24V-YELLOW
![]() |
Special Note ROLL LENGTHS_Any claim for short supply will only be considered while |
Problems | Reasons | Solutions |
---|---|---|
No illumination | No electricity supply | Ensure LED driver is working |
Automatic power protection from the open or short circuit in output of the power supply | Fix the short circuit problem | |
Wrong connection of power supply | ||
Partial illumination | Using a switching mode power supply | Make it as follows: Don’t use switching mode power supplies |
Wire connection mistake | Check connections | |
Brightness of LED is inconsistent for inconsistent | Power overloaded | Replace with a power supply that delivers 125% of current required to power the product |
Voltage drop due to exceeding max-in-series limit | Adhere to the max-in-series limit specified on the product page | |
LED Flickering | Connection point fault | Fix bad connection point |
Use a proper LED driver | Replace a new power supply |
*Note that should be cut and reconnected with end connectors for installation to avoid defects due to moisture penetration. The steps velow indicate are possible way of sealing the end:
Installation steps
![]() |
![]() |
![]() |
![]() |
Cut the neon flex | Weld the wire to the PCB board | First put silicone glue inside of the plug, and quick connector then push into the neon flex |
Wipe off the excess glue and wait for the glue to solidify. |
Cutting Mark By Every 50 mm |
Important Note
Dimensions(mm)
No account yet?
Create an Account